Baja Designs LP9 / DeWALT Utility

This is the Baja Designs LP9 Flashlight, and It is absolutely ridiculous on every single level.

Our intent was never to take it this far with the Baja Designs flashlight lineup, but after seeing the popularity with the LP6 Flashlight and the massive amount of requests for the LP9, we felt there was no choice.

Each one of these flashlights takes approximately 36 hours to make(print) from start to finish.

In order to make something of this size and caliber, we had to go through a complete re-design. We decided that with this amount of mass and weight , it would be too top-heavy if we were to design it the same way as we designed our previous models. this redesign would be the entrance to our "utility" series of flashlight housings.

There are many changes that have taken place with the LP9 flashlight. First and foremost, the battery snaps in from the back. This allows us to design it in such a way that utilizes feet for stability. These feet in the front have the option to be magnetic or not, for added stability when the flashlight is set up and being used. These feet offer added protection, as they are a separate piece from the main housing. The idea for this is so that if you were to for some reason set it down to hard and the feet break, they can be replaced and the housing would be fine. This is also what we have decided to go with for the handle. The handle is a separate piece from the main housing and bolted on during assembly. Again, this is so if you were to drop it and break the handle but the housing is fine, you could replace the handle for a new one.

The LP9 flashlight is offered with or without the option for low voltage cutoff devices. The low voltage cutoff devices are wired into both the High and Low settings for the light, and what this will do is shut down the light when the battery drops to a specified voltage, in order to protect your battery from over discharging.

We designed the LP9 light housing to be as crazy and obnoxious as possible, making it the wildest flashlight out there.

This is our highest powered and most expensive light we have to offer, so if you are looking for something completely over-the-top, slightly unnecessary, and totally awesome than this is what you're going to want. Nothing else will come close to it, not even in the slightest bit.

This housing is HUGE, not like kind of big, I mean giant. It is a massive spot light with a huge handle to hold it. I basically took our squadron flashlight and put it on huge amounts of steroids for a long period of time, and this is the result.

Each one takes 36+ hours to make, and I promise you it will put a massive smile on your face. Not to mention when you turn it on, that might throw you overboard. It's one of those things that you just want to show everybody. It's creative, unique, and there is truly nothing else like it.

This kit is offered pre-wired and pre-assembled making it plug & play right out of the box.

If you’re a person who loves to camp, off-road, explore, and/or participate in all or any thing outdoors, this light is for you.

If you are a supporter of Baja Designs due to their exceptional and powerful products than this is a unique and special way to use their lights for your camping and outdoor excursions. 

This housing is 3D printed here in the USA making the form and fit perfection.

*NONE OF THESE KITS INCLUDE THE DEWALT 20V BATTERY. THE KITS THAT ARE OPTIONED WITH THE LIGHT INCLUDED WILL COME PRE-INSTALLED AND WILL INCLUDE ALL BAJA DESIGNS ACCESSORIES THAT WOULD COME WITH THE LIGHT FROM THE FACTORY, ALONG WITH THE WARRANTY CARD, AND THE ORIGINAL BOX*

DIMENSIONS WITH BATTERY

L: 10 in

W: 9 in

H: 12 in

Weight: 10 lbs

12 gauge wires

30 amp fuse

Waterproof Factory BD Light Connectors

Spade Connectors

Stainless Bolts

Made with PETG filament, making it very heat resistant.

LP6 DeWalt 20V Housing (With or Without The Light)

Backing Plate and Bolts

On/Off/On switch (Hi/Low)

On/Off switch (Backlight)

All necessary wiring for the kit chosen

Optional low voltage cutoff device included (to protect your battery) 

Disclaimer and Warning IMPORTANT: Read Before Using Our Products

Thank you for choosing ROVRLAB.com for your 3D printed products. Please read and understand the following disclaimer and warnings before using our products.

FIRST AND FOREMOST : DURABILITY

All of our flashlight housings at the moment are 3d printed. This allows us to really have endless possibilities on the design front as far as what we can make and build. We design and manufacture all of our products in house, here in Orange County, California. 

These Flashlight housings are not intended to be the most durable, nor are we making those claims. The 3d printed PETG plastic part's durability is compromised when inserting the light and battery (which have a fair bit of weight to them). This means that if you drop the housing on concrete there is a likely chance that it can crack. Depending on the model, If you drop it on dirt it is likely the housing will be fine.

IF YOU PURCHASE ONE OF OUR FLASHLIGHT HOUSINGS, AND AT SOME POINT DURING OWNERSHIP YOU DROP THE HOUSING AND IT BREAKS/CRACKS, WE OFFER A DEEP DISCOUNT TO REPLACE IT. 

99% OF THE TIME THE LIGHT AND BATTERY ITSELF WILL BE FINE, BECAUSE THE PLASTIC PART WILL ENDURE ALL OF THE IMPACT AND TAKE THE HIT. IF THIS HAPPENS TO YOU GET IN CONTACT WITH OUR TEAM (SUPPORT@ROVRLAB.COM) AND WE CAN HELP YOU REPLACE THE HOUSING FOR A BRAND NEW ONE.

3D Printed Flashlight Housings

Our flashlight housings are designed to fit a various number of off-road light brands including Baja Designs, KC Hilights, Rigid Lights, Diode Dynamics Lights, and Morimoto Lights. These Flashlight housings utilize Milwaukee, DeWalt, or Makita batteries as the power source. These housings are 3D printed using high-quality materials, but they are not intended to withstand extreme conditions or heavy abuse. Before using the flashlight housing, please consider the following:

Safety Precautions: The light itself will generate heat during prolonged use. The Materials we use are very heat resistant and depending on the model, after testing run times and prolonged use, we can confidently say that our housings can withstand the heat coming from the light for 2+ hours continuously. We would not necessarily advise you to run them for longer than that amount of time, and we have not tested heat resistance longer than 3 hours of continuous use.

Compatibility: Ensure that the flashlight housing is compatible with your chosen light and battery, whether that be Baja Designs, KC Hilights, Rigid, Diode Dynamics, Morimoto : and paired with Milwaukee M12 or M18, DeWalt 20v, or Makita 18v battery platforms. Using an incompatible light or battery may result in improper fit or function.

Proper Use: Use the flashlight housing only as intended, following the manufacturer's instructions for both the flashlight housing and the Baja Designs light. Failure to do so may result in injury or damage to the product.

Limited Endorsement: Our flashlight housings are not manufactured by Baja Designs or Milwaukee Tool. We do have the support from Baja Designs as a company and brand, as we are now an authorized Baja Designs Dealer. Any warranties or claims regarding the lights or batteries are separate from our products and should be directed to the respective manufacturers.

Modification and Repair: Do not attempt to modify or repair the flashlight housing yourself. Any unauthorized modifications or repairs may compromise the safety and functionality of the product.

Proposition 65 Compliance (California Residents): Some materials used in our flashlight housings may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For California residents, Proposition 65 requires us to provide a clear warning about these potential risks. Please see the Proposition 65 warning on our product pages.

Disclaimer of Liability: By using our flashlight housings, you acknowledge and accept all risks associated with their use. ROVRLAB.com and its affiliates shall not be liable for any direct, indirect, incidental, special, consequential, or punitive damages resulting from the use or misuse of our products.

Use of Third-Party Products: The use of Baja Designs, KC Lights, Rigid Lights, Diode Dynamics, Morimoto lights and Milwaukee M12/M18, DeWalt 20v, and Makita 18v batteries is subject to their respective manufacturer's guidelines and safety precautions. ROVRLAB.com shall not be held liable for any issues or damages that arise from the use of these third-party products in conjunction with our flashlight housings.